• Newsteo Logger to power every sensor.

    Newsteo Logger to power different kind of voltage sensors.

    The Newsteo Logger LGW allows you to power different sensors. The sensor just needs to be connected on the Newsteo Logger. The Logger sends by radio to the supervision centre all the measures done by the sensor. The logger can also store the measures in its embedded memory.

    Sensors to connect:

    Pyranometer
    ...

    Product references (provided without sensor):

    LGW31: it has a range of measure of 0 to 3 Volt, it allows to power a sensor in 3V.
    LGW32: range of measure: 0 to 1 Volt; sensor power: 10V.
    LGW33: range of measure: 0 to 2 Volt; sensor power: 12V.
    LGW34: range of measure: 0 to 10 Volt; sensor power: 12V.
    LGW38: range of measure: 0 to 5 Volt; sensor power: 10V.

    If your sensor requires a different voltage level, please contact us.

    Newsteo also offers a range of probes which can be connected to these products:

    PYRAN-001: probe with a pyranometer. The probe can be directly connected to the LGW31.
    AIRSP-001: probe with a hot wire sensor, for air velocity measurment, with a range from 0 to 5m / s. The probe can be directly connected to the LGW38.
    Connection cables: the client can connect the sensor of his choice.

    How does it work ?

    1 - The Data Loggers
    They are spread in the area which has to be monitored. They send to the RF-to-USB key by radiofrequency the measures they take. They can be wireless configured and updated.

    2 - The RF-to-USB Key
    It is the bridge between the PC and the loggers

    3 - The RF Monitor
    This software is installed on the PC and allows the monitoring of the loggers

    The loggers can be used in two different modes:
    Recording

    Recording

    The logger records in its embedded memory the measures it takes. The user can download on the PC all the stored measures when he wants.


    Watch the video
    Monitoring

    Monitoring

    The logger sends in real time its measures to the PC. If a measure is not received by the PC, it stores it inside its internal memory and sends it to the PC on the next communication channel.

    Watch the video

  • Sensors Specifications

    LGW31 LGW32 LGW33 LGW34 LGW35 LGW38 LGW75
    Range of measure 0 to 3 Volt 0 to 1 Volt 0 to 2 Volt 0 to 10 Volt 0 to 10 Volt 0 to 5 Volt 0 to 10 Volt
    Power supply for the sensor 3 Volt / 150 mA 10 Volt 12 Volt / 100 mA 12 Volt 15 Volt 10 Volt / 100 mA 15 Volt
    Temperature Compensation Integrated temperature sensor
    Operating temperature -40°C to +85°C
    Power supply of the logger By internal battery On main power supply

    Casings Specifications



    Weight with battery
    250g

    Size
    98mm x 64mm x 34mm

    Battery
    AA (Lithium Thionyle) - 3,6V

    Antenna
    1/2 wave antenna (included)

    Casing
    Aluminium IP65

    Product Storage
    The product can be entirely set and then put in "hibernate" mode with its battery inserted. It will just be necessary to sweep a magnet on it to wake up it and to start the measurement.

    Encombrement Logger

    Other Specifications

    LGW3x LGW75
    Autonomy Up to 2 years (at 25°C with a frequency measure of 15 minutes) Illimited
    Power supply: 5 to 24 V
    Newsteo transformer available on request (reference ADAPT-003)
    Memory Retention 100 years (flash memory technology)
    Measures Frequency Can be set from one measure every seconds to one every 4 hours
    Memory Capacity Up to 32 768 mesures with date and time.

  • PYRAN-001

    5 meters with integrated pyranometer on it, for LGW31

    AIRSP-001

    AIRSP

    5 meters probe, with hot wire sensor, to measure air speed, for LGW38 :

    Measurement range: 0...5m/s
    Accuracy @ 20°C: ±0.2m/s (+3% of the measured value)
    Operating temperature: -20…60°C
    IP20

    SES55

    SES55

    Cable to connect the sensor of your choice to the LGS.
    The cable is provided with fast contactors.

  • EVALUATE THE 3V POWER SUPPLY SENSOR LOGGER


    crypto

    * Required Fields